home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Spec Disk 1998 Spring 4.0
/
Spec Disk 1998 Spring 4.0.iso
/
text
/
08565aws.txt
< prev
next >
Wrap
Text File
|
1998-06-10
|
57KB
|
1,166 lines
SECTION 08565
VINYL (PVC) WINDOWS
NOTE ** ALSIDE Window Systems vinyl windows, patio doors,
and specialty windows.
NOTE **
NOTE ** This section is based on products manufactured by:
NOTE ** ALSIDE Window Systems
NOTE ** P.O. Box 2010 Akron OH 44309
NOTE ** Tel: (800) 257-4335
NOTE ** Fax: (330) 922-5387
NOTE **
NOTE ** ALSIDE Window Systems offer a full selection of
vinyl windows, patio doors, and specialty windows.
NOTE **
NOTE ** SECTION 08565 - VINYL (PVC) WINDOWS, Copyright
1998, The Architect's Catalog, Inc.
PART 1 GENERAL
1.1 SECTION INCLUDES
A. Single Hung Window Units.
B. Double Hung Window Units.
C. Horizontal Sliding Window Units.
D. Horizontal Sliding Patio Door Units.
E. Casement Window Units.
1.2 RELATED SECTIONS
NOTE ** Delete any sections below not relevant to this
project; add others as required.
A. Section 05400 - Cold Formed Metal Framing.
B. Section 06100 - Rough Carpentry.
C. Section 07900 - Joint Sealers.
D. Section 09100 - Metal Support Systems.
1.3 REFERENCES
NOTE ** Delete any references below not relevant to this
project; add others as required.
A. AAMA 101 - Voluntary Standard for Aluminum and Poly
(Vinyl Chloride) (PVC) Prime Windows and Glass Doors.
B. NFRC 100 - Thermal Properties; National Fenestration
Rating Council.
C. ASTM D 3656 - Standard Specification for Insect Screening
and Louver Cloth Woven from Vinyl-Coated Glass Fiber
Yarn.
D. ASTM D 3678 - Standard Specification for Rigid Poly
(Vinyl Chloride) (PVC) Interior Profile Extrusions.
E. ASTM D 4028 - Standard Specification for Solar Screening
Woven from Vinyl-Coated Fiber Glass Yarn.
F. ASTM D 4099 - Standard Specification for Poly (Vinyl
Chloride) (PVC) Prime Windows/Sliding Glass Doors.
G. ASTM E 774 - Standard Specification for Sealed Insulating
Glass.
H. IGCC - Classification of Insulating Glass Units;
Insulated Glass Certification Council.
1.4 SUBMITTALS
A. Submit under provisions of Section 01300.
B. Product Data: Manufacturer's standard details and
catalog data demonstrating compliance with referenced
standards; include manufacturer's standard installation
instructions.
C. Drawings: Manufacturer's product drawings showing
details of fabrication, hardware, weatherstripping,
fasteners, screens, glazing, accessories, and related
items.
D. Verification Samples: Operating sample of each window
type specified illustrating fabrication, hardware,
glazing, screen, and finish.
E. Test Reports: For each window type specified, furnish
test reports from accredited independent testing
laboratory certifying that identical or larger window
units meet requirements specified for air infiltration,
water penetration and structural performance by ASTM D
4099 or AAMA 101, for thermal performance by NFRC, and
for seal integrity of insulating glass units by IGCC.
F. Closeout Submittals: Warranty documents, properly
executed.
1.5 QUALITY ASSURANCE
A. Manufacturer Qualifications: Minimum ten (10) years
experience producing vinyl (PVC) windows.
1.6 DELIVERY, STORAGE AND HANDLING
A. Deliver windows to project site in undamaged condition;
handle windows to prevent damage to components and to
finishes.
B. Store windows out of contact with ground; protect windows
from weather and construction traffic in well-ventilated
area.
1.7 WARRANTY
A. Furnish manufacturer's standard warranty against
deficiencies in materials or fabrication.
PART 2 PRODUCTS
2.1 MANUFACTURERS
A. Acceptable Manufacturer: ALSIDE Window Systems;, P.O.
Box 2010 Akron, OH 44309; ASD. Tel: (800) 257-4335, Fax:
(330) 922-5387.
B. Substitutions: Not permitted.
NOTE ** Delete the following Article if no single-hung
window units required.
2.2 SINGLE HUNG WINDOW UNITS
NOTE ** Retain the following paragraph if specifying ALSIDE
0500 single-hung window units.
A. Acceptable Product: ALSIDE MODEL 0500.
1. Grade: ASTM D 4099 Grade 40, AAMA 101 Grade R40, for
48-inch wide by 72-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 4.5 pounds per square foot.
b. Air infiltration: 0.15 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.50.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.33.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, overlapping butt-joint
construction, joined with screws into integral screw
ports; sloped sill for positive drainage.
8. Sash: PVC extrusions, tilt-in operation of lower
sash for cleaning, with spiral balances, integral
double walled lift rail for added strength,
interlocking with fixed meeting rail of main frame,
and cam-type sweep locks and keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
0100 single-hung new construction window units in
Grade 20.
B. Acceptable Product: ALSIDE MODEL 0100.
1. Grade: ASTM D 4099 Grade 20, AAMA 101 Grade R20, for
48-inch wide by 72-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 3.0 pounds per square foot.
b. Air infiltration: 0.10 cubic feet per minute per
linear foot at 25 miles per hour.
c. Test pressure sustained without damage: 30
pounds per square foot.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.50.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.31.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 3/4 inch unit
thickness, with SSB glass.
5. Glazing: Low-e sealed insulating glass unit, 3/4
inch unit thickness, with SSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners.
8. Sash: Narrow-line fusion-welded PVC extrusions,
mitered corners, tilt-in operation of lower sash for
cleaning, with spiral balances, integral lift rail
for added strength, interlocking with fixed meeting
rail of main frame, and cam-type sweep locks and
keepers.
9. Nailing fin: Extruded PVC, 1-1/8 inches wide, four
sides.
10. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
11. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Delete the following Article if no double-hung
window units required.
2.3 DOUBLE HUNG WINDOW UNITS
NOTE ** Retain the following paragraph if specifying ALSIDE
0901 double-hung window units.
A. Acceptable Product: ALSIDE MODEL 0901.
1. Grade: ASTM D 4099 Grade 40, AAMA 101 Grade R40, for
48-inch wide by 72-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 5.0 pounds per square foot.
b. Air infiltration: 0.16 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.50.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.34.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, telescoping butt-joint
construction reinforced at corners, joined with
screws into integral screw ports; sloped sill for
positive drainage.
8. Sash: PVC extrusions, aluminum reinforced horizontal
members for window units over 28-7/8 inches wide,
tilt-in operation of upper and lower sash for
cleaning, with field-adjustable spiral balances,
integral double walled lift rail for added strength,
interlocking meeting rails and cam-type sweep locks
and keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
0601 double-hung window units in standard Grade 45.
B. Acceptable Product: ALSIDE MODEL 0601.
1. Grade: ASTM D 4099 Grade 45, AAMA 101 Grade R45, for
47-inch wide by 60-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 6.0 pounds per square foot.
b. Air infiltration: 0.13 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.47.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.32.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners; concealed screen track.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, mitered corners, tilt-in operation of
upper and lower sash for cleaning, with field-
adjustable spiral balances, double lift rail on
bottom sash, interlocking meeting rails, and cam-type
sweep locks and keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
3001 double-hung window units.
C. Acceptable Product: ALSIDE MODEL 3001.
1. Grade: ASTM D 4099 Grade 45, AAMA 101 Grade R45, for
48-inch wide by 72-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 4.5 pounds per square foot.
b. Air infiltration: 0.19 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.49.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.34.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 15/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 15/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, butt-joint construction,
sloped hospital sill for positive drainage.
8. Sash: PVC extrusions, mitered corners joined with 4
screws per corner into heavy duty corner gussets;
tilt-in operation of upper and lower sash for
cleaning, with field-adjustable spiral balances;
integral double walled lift rail for added strength,
interlocking meeting rails on top and bottom sash,
and cam-type sweep locks and keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete options specified in the following two
paragraphs if not required.
10. Reinforcement: Steel reinforced frame and/or sash.
11. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
O201 double-hung window units.
D. Acceptable Product: ALSIDE MODEL O201.
1. Grade: ASTM D 4099 Grade 30, AAMA 101 Grade R30, for
48-inch wide by 60-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 4.5 pounds per square foot.
b. Air infiltration: 0.15 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.51.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.36.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners; sloped sill for positive drainage.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, mitered corners, tilt-in operation of
upper and lower sash for cleaning, with field-
adjustable spiral balances, interlocking meeting
rails, and cam-type sweep locks and keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
0401 double-hung window units.
E. Acceptable Product: ALSIDE MODEL 0401.
1. Grade: ASTM D 4099 Grade 35, AAMA 101 Grade R35, for
36-inch wide by 60-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 4.50 pounds per square
foot.
b. Air infiltration: 0.15 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.49.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.33.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, telescoping butt-joint
construction reinforced at corners, joined with
screws into integral screw ports; sloped sill for
positive drainage.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, mitered corners, tilt-in operation of
upper and lower sash for cleaning, with field-
adjustable spiral balances, double lift rail on
bottom sash, interlocking meeting rails, and cam-type
sweep locks and keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
F. Acceptable Product: ALSIDE MODEL 0301.
1. Grade: ASTM D 4099 Grade 30, AAMA 101 Grade R30, for
48-inch wide by 60-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 4.5 pounds per square foot.
b. Air infiltration: 0.15 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.51.
3. Thermal performance, in accordance with NFRC 100, for
48-inch wide by 72-inch high window unit: U-Value
0.36.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 3/4 inch unit
thickness, with SSB glass.
5. Glazing: Low-e sealed insulating glass unit, 3/4
inch unit thickness, with SSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners; sloped sill for positive drainage,
integral J-channel.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, mitered corners, tilt-in operation of
upper and lower sash for cleaning, with field-
adjustable spiral balances, interlocking meeting
rails, and cam-type sweep locks and keepers.
9. Nailing fin: Extruded PVC, four sides, 1.75 wide.
10. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
11. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Delete the following Article if no horizontal-
sliding window units required.
2.4 HORIZONTAL SLIDING WINDOW UNITS
NOTE ** Retain the following paragraph if specifying ALSIDE
0902 horizontal-sliding window units.
A. Acceptable Product: ALSIDE MODEL 0902.
1. Grade: ASTM D 4099 Grade 40, AAMA 101 Grade R40, for
72-inch wide by 48-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 4.5 pounds per square foot.
b. Air infiltration: 0.20 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.50.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.34.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, butt-joint construction at
corners, joined with screws into integral screw
ports; multi-chambered weep system with wind-blocking
covers.
8. Sash: PVC extrusions, aluminum-reinforced vertical
members for window units over 29-1/2 inches high,
lift-out operation of both operable sash units, with
nylon-encased metal dual-roller system, full-
interlocking meeting rails, full sash capture at
jamb, sash vent lock, theft-deterrent blocks, and cam-
type sweep locks and keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
0602 horizontal-sliding window units.
B. Acceptable Product: ALSIDE MODEL 0602.
1. Grade: ASTM D 4099 Grade 50, AAMA 101 Grade R50, for
72-inch wide by 51-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 6.5 pounds per square foot.
b. Air infiltration: 0.20 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.47.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.31.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners; step sill for positive drainage,
concealed screen track.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, mitered corners, lift-out operation of
both operable sash units, with nylon-encased metal
dual-roller system, full-interlocking meeting rails,
full sash capture at jamb, sash vent lock, theft-
deterrent blocks, cam-type locks with keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
3002 horizontal-sliding window units.
C. Acceptable Product: ALSIDE MODEL 3002.
1. Grade: ASTM D 4099 Grade 50, AAMA 101 Grade R50, for
72-inch wide by 50-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 5.0 pounds per square foot.
b. Air infiltration: 0.16 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.49.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.35.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 15/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 15/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners.
8. Sash: PVC extrusions, mitered corners with heavy
duty corner gussets secured by four (4) screw
fasteners each corner, lift-out operation of both
operable sash units, with nylon-encased metal dual-
roller system, full-interlocking meeting rails, full
sash capture at jamb, sash vent lock, theft-deterrent
blocks, dual chrome-plated cam-type locks with
stainless steel keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
0102 horizontal-sliding window units.
D. Acceptable Product: ALSIDE MODEL 0102.
1. Grade: ASTM D 4099 Grade 25, AAMA 101 Grade R25, for
72-inch wide by 48-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 5.25 pounds per square
foot.
b. Air infiltration: 0.10 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.50.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.31.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 3/4 inch unit
thickness, with SSB glass.
5. Glazing: Low-e sealed insulating glass unit, 3/4
inch unit thickness, with SSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners; weeps in sill for positive drainage,
extruded PVC nailing fin four (4) sides.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, mitered corners, lift-out operation of
operable sash unit, with full-interlocking meeting
rail, full sash capture at jamb, cam-type locks with
keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
O202 horizontal-sliding window units.
E. Acceptable Product: ALSIDE MODEL O202.
1. Grade: ASTM D 4099 Grade 40, AAMA 101 Grade R40, for
60-inch wide by 36-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 6.0 pounds per square foot.
b. Air infiltration: 0.12 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.49.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.35.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners; weeps in sill for positive drainage.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, lift-out operation of both operable
sash units, with nylon-encased metal dual-roller
system, full-interlocking meeting rails, full sash
capture at sill, cam-type locks with keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Retain the following paragraph if specifying ALSIDE
O402 horizontal-sliding window units.
F. Acceptable Product: ALSIDE MODEL O402.
1. Grade: ASTM D 4099 Grade 40, AAMA 101 Grade R40, for
72-inch wide by 48-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 5.25 pounds per square
foot.
b. Air infiltration: 0.20 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.49.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 48-inch high window unit: U-Value
0.33.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, butt-joint construction at
corners, joined with screws into integral screw
ports; multi-chambered weep system with wind-blocking
covers.
8. Sash: PVC extrusions, fusion-welded narrow-line
construction, mitered corners, lift-out operation of
both operable sash units, with nylon-encased metal
dual-roller system, full-interlocking meeting rails,
full sash capture at jamb, cam-type locks with
keepers.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
NOTE ** Delete the following Article if no horizontal-
sliding patio door units required.
2.5 HORIZONTAL SLIDING PATIO DOOR UNITS
NOTE ** Retain the following paragraph if specifying ALSIDE
6100 horizontal-sliding patio door units.
A. Acceptable Product: ALSIDE MODEL 6100.
1. Grade: ASTM D 4099 Grade 35, AAMA 101 Grade R35, for
69-inch wide by 79-inch high door unit; exceeding
grade requirements as follows:
a. Water test pressure: 4.5 pounds per square foot.
b. Air infiltration: 0.15 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional colonial grooved or tinted glazing is
specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 96-inch high door unit: U-Value
0.54.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 96-inch high door unit: U-Value
0.39.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Colonial grooved glazing and
tinted glazing are options; consult with
manufacturer.
4. Glazing: Sealed insulating glass unit, 7/8 inch unit
thickness, with fully-tempered DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 7/8
inch unit thickness, with fully-tempered DSB glass
and argon gas fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: Vinyl-clad wood, triple-screw butt-joint
construction; sloped vinyl sill with steel roller
track.
8. Sash: PVC extrusions, butt-joint construction, steel-
reinforced vertical members, operable sash unit with
adjustable dual-roller system, full-interlocking
meeting rails, full sash capture at jamb, and
latching hardware with keeper.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement; four-point adjustable rollers.
NOTE ** Delete the options in the following four paragraphs
if not required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
11. Hardware operation: Keyed lock on exterior side,
with two (2) keys.
12. Hardware finish: Brass.
13. Vent lock.
NOTE ** Retain the following paragraph if specifying ALSIDE
2100 horizontal-sliding patio door units.
B. Acceptable Product: ALSIDE MODEL 2100.
1. Grade: ASTM D 4099 Grade 30, AAMA 101 Grade R30, for
72-inch wide by 80-inch high door unit; exceeding
grade requirements as follows:
a. Water test pressure: 3.75 pounds per square
foot.
b. Air infiltration: 0.09 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional colonial grooved or tinted glazing is
specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 96-inch high door unit: U-Value
0.50.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 96-inch high door unit: U-Value
0.34.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Colonial grooved glazing and
tinted glazing are options; consult with
manufacturer.
4. Glazing: Sealed insulating glass unit, 7/8 inch unit
thickness, with fully-tempered DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 7/8
inch unit thickness, with fully-tempered DSB glass
and argon gas fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, mechanical butt-joint
construction, stainless steel track; sloped vinyl
sill for positive drainage.
8. Sash: PVC extrusions, fusion-welded construction,
mitered corners, steel-reinforced vertical members on
operable panel, operable sash unit with adjustable
dual-roller system, full-interlocking meeting rails,
full sash capture at jamb, and latching hardware with
keeper.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement; four-point adjustable rollers.
NOTE ** Delete options specified in the following two sub-
paragraphs if not required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
11. Hardware operation: Keyed lock on exterior side,
with two (2) keys.
NOTE ** Retain the following paragraph if specifying ALSIDE
1100 horizontal-sliding patio door units.
C. Acceptable Product: ALSIDE MODEL 1100.
1. Grade: ASTM D 4099 Grade 30, AAMA 101 Grade R30, for
72-inch wide by 80-inch high door unit; exceeding
grade requirements as follows:
a. Water test pressure: 3.75 pounds per square
foot.
b. Air infiltration: 0.09 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional colonial grooved or tinted glazing is
specified.
2. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 96-inch high door unit: U-Value
0.49.
3. Thermal performance, in accordance with NFRC 100, for
72-inch wide by 96-inch high door unit: U-Value
0.34.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Colonial grooved glazing and
tinted glazing are options; consult with
manufacturer.
4. Glazing: Sealed insulating glass unit, 7/8 inch unit
thickness, with fully-tempered DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 7/8
inch unit thickness, with fully-tempered DSB glass
and argon gas fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners; vinyl sill with aluminum roller
track.
8. Sash: PVC extrusions, fusion-welded construction,
mitered corners, steel-reinforced vertical members on
operable sash unit with adjustable dual-roller
system, full-interlocking meeting rails, full sash
capture at jamb, and latching hardware with keeper.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement; four-point adjustable rollers.
NOTE ** Delete options specified in the following two sub-
paragraphs if not required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
11. Hardware operation: Keyed lock on exterior side,
with two (2) keys.
NOTE ** Delete the following Article if no casement window
units required.
2.6 CASEMENT WINDOW UNITS
NOTE ** Retain the following paragraph if specifying ALSIDE
0961 casement window units.
A. Acceptable Product: ALSIDE MODEL 0961.
1. Grade: ASTM D 4099 Grade 50, AAMA 101 Grade R50, for
26-inch wide by 50-inch high window unit; exceeding
grade requirements as follows:
a. Water test pressure: 5.25 pounds per square
foot.
b. Air infiltration: 0.04 cubic feet per minute per
linear foot at 25 miles per hour.
NOTE ** Delete one of the following two sub-paragraphs;
first is for standard glazing, second is for low-e
glazing with argon gas fill. Consult with
manufacturer for thermal performance data if
optional obscure or tinted glazing is specified.
2. Thermal performance, in accordance with NFRC 100, for
30-inch wide by 60-inch high window unit: U-Value
0.44.
3. Thermal performance, in accordance with NFRC 100, for
30-inch wide by 60-inch high window unit: U-Value
0.30.
NOTE ** Delete one of the following two sub-paragraphs to
specify glazing type required; first is for
standard glazing, second is for low-e glazing with
argon gas fill. Obscure glazing and tinted glazing
are options; consult with manufacturer.
4. Glazing: Sealed insulating glass unit, 13/16 inch
unit thickness, with DSB glass.
5. Glazing: Low-e sealed insulating glass unit, 13/16
inch unit thickness, with DSB glass and argon gas
fill.
6. Sealed Insulating Glass Units: Conform to ASTM E
774, Level CBA, utilizing PPG Warm-Edge "Intercept"
Spacer System.
7. Frame: PVC extrusions, fusion-welded construction,
mitered corners.
8. Sash: PVC extrusions, fusion-welded construction,
mitered corners, operable sash unit with single-
handle multi-point locking system, positive-action
rotary-crank operator system, with handle.
9. Insect screening: Roll-formed or extruded aluminum
channel frames, with 18 by 16 fiberglass mesh secured
with continuous vinyl gasket, removable for screen
replacement.
NOTE ** Delete the following paragraph if muntins are not
required.
10. Muntins: Colonial grid installed between outer and
inner glass panes during fabrication of insulating
glass units.
2.7 FABRICATION
A. Window/Door Units: Assemble units completely in factory,
including operating hardware and glazing.
PART 3 EXECUTION
3.1 EXAMINATION
A. Verification of Conditions: Openings are in correct
location, and of correct size, in accordance with
approved shop drawings and manufacturer's installation
instructions.
B. Installer's Examination:
1. Have installer of this section examine conditions
under which construction activities of this section
are to be performed, then submit written notification
if such conditions are unacceptable.
2. Transmit two copies of installer's report to
Architect within 24 hours of receipt.
3. Beginning construction activities of this section
before unacceptable conditions have been corrected is
prohibited.
4. Beginning construction activities of this section
indicates installer's acceptance of conditions.
3.2 INSTALLATION
A. Install products specified in this section square, plumb
and level, in accordance with approved shop drawings and
manufacturer's installation instructions.
B. Installation of joint sealers is specified in Section
07900.
3.3 ADJUSTING
A. Adjust operating hardware for correct operation in
accordance with manufacturer's installation instructions.
3.4 CLEANING
A. Clean interior and exterior surfaces free of labels,
mortar, plaster, paint, joint sealers, and other foreign
matter to prevent damage to weatherstrip, and to prevent
interference with operation of hardware.
3.5 PROTECTION
A. Protect ventilators and operating parts from dirt and
damage caused by subsequent construction activities.
B. Replace units damaged by subsequent construction
activities.
END OF SECTION
